SUBERSIBLE TURBIN PUMP 2HP MEREK FE PETRO

Power Requirements > 1-1/ 2 hp Fixed Speed models require single phase, 208-230 VAC, 60 Hertz incoming power > 1-1/ 2 hp Fixed Speed models incorporate a starting & running capacitor, with internal bleed resistor, rated 370 Volt, 15 microfarad > STP-SCI Single Phase Smart Controllers and STP-CBS Single Phase Control Boxes are available for 1 1/ 2 hp pump control > Max Motor Draw: 11 amps Pump Motor > 1-1/ 2 hp Fixed Speed, 3450 rpm, multi-stage centrifugal type pump motor with integral, automatic, thermal overload protection > Available in Standard Pressure ( 2 stage) model, Max Flow = 100 gpm, Max Pressure = 34 psi > Available in High Pressure ( H150, 3 stage) model, Max Flow = 65 gpm, Max Pressure = 46 psi > Max liquid viscosity: 70 SSU @ 60° F ( 15° C) > Standard STP ( Non-AG) models are UL and cUL listed for fuel mixtures containing up to 10% Ethanol or Methanol, and 20% MTBE, 20% ETBE, or 17% TAME with gasoline. > STPAG ( Alcohol-Gasoline) models are UL and cUL listed for fuel mixtures containing up to 85% Ethanol or Methanol, and 20% MTBE, 20% ETBE, or 17% TAME with gasoline. > 1-1/ 2hp Fixed Speed models can also be used with Diesel Fuels, Fuel Oils, Kerosene, Avgas, and Jet Fuels in a non-gelled pourable state. > All wetted elastomers are made of a high grade, fluorocarbon viton compound. Standard Features > 1-1/ 2 hp Fixed Speed models are available in Variable Length and Fixed Length options > Check Valve: 2 3/ 4 diameter fluorocarbon viton seal constructed on cast aluminum body and steel backing washer > Pressure Relief Valve: available in four pressure relief settings, integral to Check Valve. Standard Model relieves at 40 psi and resets above 35 psi. > Syphon: venturi type syphon primer supplied with every submersible. Syphon Check Valve and Secondary Syphon sold separately. > Air Eliminator: every submersible includes tank return path, with one-way check valve, to provide active air elimination > Electrical Disconnect: electrical yoke for positive contractor disconnect during service Approvals > 1 1/ 2 hp Fixed Speed models are UL and cUL listed > Consult factory for other applicable approvals Quality Certification > Franklin Fueling Systems is an ISO 9001 Certified Manufacturer Ordering Information 1-1/ 2 hp Fixed Speed, Variable Length Submersible Turbines Pumps Non-AG Model Number Description Model* Length Range STP 150 - VL1 1 1/ 2 hp Fixed Speed 60” -88” STP 150 - VL2 1 1/ 2 hp Fixed Speed 91” -152” STP 150 - VL3 1 1/ 2 hp Fixed Speed 123” -214” STP H 150 - VL1 High Pressure, 1 1/ 2 hp Fixed Speed 61” -89” STP H 150 - VL2 High Pressure, 1 1/ 2 hp Fixed Speed 92” -152” STP H 150 - VL3 High Pressure, 1 1/ 2 hp Fixed Speed 124” -215” Alcohol-Gasoline Model Number Description Model* Length Range STPAG 150 - VL1 AG, 1 1/ 2 hp Fixed Speed 60” -88” STPAG 150 - VL2 AG, 1 1/ 2 hp Fixed Speed 91” -152” STPAG 150 - VL3 AG, 1 1/ 2 hp Fixed Speed 123” -214” STPAG H 150 - VL1 AG, High Pressure, 1 1/ 2 hp Fixed Speed 61” -89” STPAG H 150 - VL2 AG, High Pressure, 1 1/ 2 hp Fixed Speed 92” -152” STPAG H 150 - VL3 AG, High Pressure, 1 1/ 2 hp Fixed Speed 124” -215” 1. Above models are UL and cUL listed for compatibility with fuel mixtures containing: STP ( Non-AG) = up to 15% Ethanol or Methanol with Gasoline, and 20% MTBE, 20% ETBE, or 17% TAME with Gasoline. STPAG ( Alcohol-Gasoline) = up to 100% Ethanol or Methanol with Gasoline, and 20% MTBE, 20% ETBE, or 17% TAME with Gasoline. 2. All models are supplied with Standard Check Valve unless factory option “ R” or “ W” is specified. 3. All above models require Single Phase, 208-230 VAC, 60 Hertz incoming power * Model Length ( B) defined as the dimension from Turbine Manifold bottom to Pump Motor inlet. * * 4” Riser Pipe, if supplied locally, must be 4 1/ 2” OD by 3/ 16” wall thickness tubing. * * * For Riser Pipe lengths 31” to 69” , adder charge applies. Factory Installed Options ( specified in Model Number at time of STP order) Model Designation Description F Floating Suction Adapter ( 1 1/ 2” NPT Female) must be factory installed K IFS ( Intake Filter Screen) factory assemblied to Pump Motor Assembly R Model R Check Valve factory installed ( for Veeder Root PLLD Line Leak) W Model W Check Valve factory installed ( for Red Jacket PPM4000 Line Leak) Field Installed Options ( 1-1/ 2 hp Fixed Speed specific accessories) Part Number Description 5800100215 Single Phase Smart Controller ( when purchased without a 4 inch STP) 5800100215 Single Phase Smart Controller ( when purchased with a 4 inch STP) * 5800300100 STP-SCI ( Dispenser Hook Isolation for 110V dispenser handle switches, up to 8 each) 402312921 STP-DHI-SCI ( combo Dispenser Hook Isolation with factory wired STP-SCI) * 402313921 STP-DHI-CBS ( combo Dispenser Hook Isolation with factory wired STP-CBS) 400818921 STP-CBS ( Single Phase Control Box with lockout switch, 110V coil) 400137908 Syphon Check Valve ( Alcohol-Gasoline compatible) when ordered with STP 402507930 Secondary Syphon Kit ( when two syphon primes are required for one STP) 402459931 Model 65 PSI Check Valve ( for Slave of manifolded STP’ s with Veeder Root PLLD)